Optimization of wear by addition of silicon for tribological applications-A Review

July 2017
Vol-3, Issue-4
Paper ID: 6214
ISSN: 2395-4396
Downloads: 66
Download PDF

Abstract & Details

Research Area
friction and wear
Keywords
Wear Properties Taguchi Method Pin- on -Disc machine
Abstract
Abstract-Zinc Aluminum Alloys over the past decayed are occupying attention of both researches and industries as a promising material for tribological applications. At this moment commercially available Zinc-Aluminum (ZA) alloys and bearing bronzes due to good cost ability and unique combination of properties. They can also be considered as competing material for cast iron, plastics and even for steels. It has been shown that the addition of alloying elements including copper, silicon, magnesium, manganese and nickel can improve the mechanical and tribological properties of zinc aluminum alloys. This alloy has still found limited applications involving high stress conditions due to its lower creep resistance, compared to traditional aluminum alloys and other structural materials especially at temperature above 100 degree Celsius. This has resulted in major loss of market potential for those alloy otherwise it is excellent material. Recently it has been shown that these problems can overcome to great extent by replacing Zinc with aluminum. Extensive research on the new alloys resulted in the development of ternary Al-40Zn-3Cu and Al-25Zn-3Cu and quaternary Al-40Zn-3Cu-2Si and Al-40Zn-3Cu-(1-3) Si alloys. They were found to be comparable to the zinc based commercial alloys as far as their specific strength and wear resistance are concerned but considerably higher ductility and dimensional change. In this paper there is discussion of the effect of Silicon on tribological properties of aluminium based Zinc alloy.

Author Information

# Name Institute / Affiliation
1 Arun c. Pund Dr. D. Y. Patil Institute of engineering and technology
2 Prof. P R Sonawane Dr. D.Y. pATIL INSTITUE OF ENGINEERING AND TECHNOLOGY

How to Cite

Use the following formats to cite this article in your research.

APA Style
Pund, Arun c. & Sonawane, Prof. P R (2017). Optimization of wear by addition of silicon for tribological applications-A Review. International Journal of Advance Research and Innovative Ideas In Education, 3(4), 2268-2274.
MLA Style
Pund, Arun c., and Prof. P R Sonawane. "Optimization of wear by addition of silicon for tribological applications-A Review." International Journal of Advance Research and Innovative Ideas In Education, vol. 3, no. 4, 2017, pp. 2268-2274.
IEEE Style
Arun c. Pund and Prof. P R Sonawane, "Optimization of wear by addition of silicon for tribological applications-A Review," International Journal of Advance Research and Innovative Ideas In Education, vol. 3, no. 4, pp. 2268-2274, 2017.
Vancouver Style
Pund Arun c., Sonawane Prof. P R. Optimization of wear by addition of silicon for tribological applications-A Review. International Journal of Advance Research and Innovative Ideas In Education. 2017;3(4):2268-2274.
Harvard Style
Pund, Arun c. & Sonawane, Prof. P R (2017) 'Optimization of wear by addition of silicon for tribological applications-A Review', International Journal of Advance Research and Innovative Ideas In Education, 3(4), pp. 2268-2274.
Chicago Style
Pund, Arun c. and Prof. P R Sonawane. "Optimization of wear by addition of silicon for tribological applications-A Review." International Journal of Advance Research and Innovative Ideas In Education 3, no. 4 (2017): 2268-2274.
Turabian Style
Pund, Arun c. and Prof. P R Sonawane. "Optimization of wear by addition of silicon for tribological applications-A Review." International Journal of Advance Research and Innovative Ideas In Education 3, no. 4 (2017): 2268-2274.

Export Citation